1990's Anodized CNC Era Bike Parts

Paul Boxcar Stem: 70mm x 15D x 31.8mm - Pink / Black (Near Mint+)

Cool pink and black colorway on the legendary . Made in the USA, lighter & stronger than Thomson! Condition Near mint or better with low miles. Hardly a mark, though the pink ano is a bit faded   Details 1 1/8" threadless 70mm x 15...

Avid Tri Align Cantilever Brake Arms: Matched Front & Rear Set - Black

These brakes came in a long arm version (3 3/8") and short arm (3").  This set has one of each.  People often put long brake arms on the front for extra power, and a short on the rear.  The arms come with pad retainers/bolts and bushings,...

Avid SD Ultimate Brake Lever: RIGHT Only - Black Anodized - Vintage 1990's (EXC)

Avid's top of the line brake levers!  These tend to have a bit better modulation than the ultra lightweight 90's CNC levers like the Kooka and Paul levers.  Plus, they look amazing!  This is only the right side lever Condition Excellent...

NIB/NOS Salsa Moto Threadless MTB Stem: 1 1/8" x 120mm x 25.4mm x Zero Rise (Installed?)

Lovely Salsa stem with zero rise!  These are like candy for 90's MTB kids. Condition New old stock with retail bag and manual! It does look like it's been test fit on a steerer, but a handlebar has never been installed. The only wear to note is...

Control Tech Stix Stumpy Bar Ends: Short Stubby Version - Vintage 1990's - Black (Near Mint+)

Rare short and stubby version of Control Tech's 1990's bar ends, officially named the Control Stix Stumpy. Condition Near mint or better with very few miles. Only a few very minor marks. Details Black

NOS Shimano XTR FD-M950 Front Derailleur: 28.6mm - Top Swing/Low Clamp (Slight Shop Wear)

Top shelf front mech for 8 and 9 speed drivetrains. Condition New old stock with slight shop wear Details Clamp: 28.6mm Top pull Top swing

Shimano XTR HB-M900 Front Hub: 36H (Perfect Bearings Near Mint+ Low Miles)

Attractive hub from the 1st generation XTR M900 group. Condition Near mint or better with very few miles. Some light cosmetic wear. Bearings feel new. Barely any spoke hole wear.  Details 36 hole

NOS Scott Mathauser Superbrake Pad Inserts: Size "S" for Finned Holders (Sold in Pairs)

Set of four brake shoes, in size "S" to fit Mathauser finned Superbrake pad holders.   Condition New old stock. Pads are supple and not at all drying. Details Sold in pairs (for a whole bike front and rear, order quantity two) Salmon 

Shimano Deore XT II SL-M732 REAR Thumb Shifter: 7 Speed SIS / Friction (Near Mint+ Low Miles)

Clean XT thumbie! These last generation XT shifters ran from 1989 to 1992, and Shimano went Rapidfire shifter only in catalogs in 1993. These were likely issued for a year or two after 1992 for bikes that desired thumbies.   Condition Near...

EDCO Competition Hubset: 36H x 8/9sp Cassette - 135mm - Polished (Near Mint+ Perfect Bearings)

High quality Swiss-made rear mountain bike hubset from the 1990's.  They're ultra smooth, bombproof, quite rare. Condition Near mint or better with low miles. Perfect bearings.  There's slight spoke hole wear and a touch of dirt in deep...

NIB/NOS Shimano XTR CN-IG90 Chain: 7/8 Speed -116L - M900 + M950 + Dura Ace 7400

This chain was part of the 1st Generation XTR M900 group and later M950 group as well as the Dura Ace 7400 series, and was the top chain available in the early 1990's.  It was often an upgrade to M737 and M739 groups, or Dura Ace / 600 on the road...

Brodie Brake Booster / Fork Arch: Rockshox Judy - 3DV Purple 1990's Ano - Cable Hanger (Near Mint)

Super rare 3D Violet brake booster from Paul Brodie's workshop, circa 1990's. This version is scarcely seen, while the Brodie magnesium cantilever booster with a more rounded shape and no cable stop is more common. Cheap way to add some OG 3DV bling to...

Chris King 1 1/8" NoThreadSet Threadless Headset: Black (EXC)

Nice CK headset for your 1 1/8" fork.   Condition: Excellent lightly used shape. Bearings feel wonderful. Cups are slightly faded, top race and cap are not faded. A touch of very light cosmetic wear, nothing worth noting Details: Size: 1...

Machine Tech Zero Flex QL Right/Rear Brake Lever: Vintage 1990's Cantilever - Silver

These rad levers were made in the USA from ~1996 to 1997 (via MOMBAT Timeline).  They released with the Machine Tech Zero Flex Cantilever brakes, and were reviewed as some of the best performing mtb brake levers of the era.  They are much...

Ringle Zooka Threadless Stem Body: 1 1/8" x 135mm x 25.4mm (EXC, No Faceplate or Cam Bolt)

Rare anodized stem from the 1990's, in one of the most popular colors.  Finding these in turquoise is pretty tough!  Great for your Yeti restoration. This one is missing it's faceplate and it's cam bolt. It's just the body with no hardware. Mix...

Kooka Racha Brake Levers: Red Ano - 1990's Cantilever (EXC+)

Kooka Racha's are some of the most popular (and for good reason) cantilever brake levers from the 90's CNC era.  They look lovely and edgy at the same time plus add power/modulation to any brake you hook them up to.   Condition Excellent...

NOS Two-Pin Dust Caps: Deeper Than Most - Chrome Plated Plastic

2-pin dust caps that look very similar to XT FC-M730 caps, but are a lot deeper front to back. Unsure who made these or why they're so deep. Condition New old stock! Slightest hints of shop wear microscratching Details Pair

NOS Two-Pin Dust Caps: Chrome Plated Plastic

2-pin dust caps that look very similar to XT FC-M730 caps. Condition New old stock! Slightest hints of shop wear microscratching Details Pair

NOS Shimano XT FC-M730 / FC-M730 Dust Caps: 2 Pin - Chrome Plated Plastic

Clean caps for your 1980's Shimano XT cranks! These cosmetically look the same as XTR FC-M900 1st gen cranks, and look great on Dura Ace 7400/7402 cranks, as they use the two-pin style too. Condition New old stock! Slightest hints of shop wear...

NOS Grafton Pedal Clipless Tension Elastomers: Set of 8 - Speedtrap / Speedlite - 3.38mm Thick Extra Firm?

These elastomers came to me in the bag with all my Grafton cleat/pedal parts and appear identical to the original SpeedTrap tension elastomers, just thicker. These measure 3.38mm thick. Is this just an extra firm version? Condition New old stock,...

NIB/NOS Grafton Pedal Cage Plate Bolts: Set of 8 - Speedtrap / Speedlite

Fresh set of original 1990's bolts to attach your cages to the bodies on all Grafton Speedtrap / Speedlite pedals. Condition New old stock in retail bag Details Set of 8 bolts (enough for two pedals)  

Grafton Speedtraps Pedal/Cleat Parts LOT: Elastomers / Wing Protectors / Cleat Bolts & Screws / Plugs / Plastic Shims (NOS & Used)

Little lot of replacement parts for Grafton cleats plus pedal clip in tension elastomers. Condition Some parts are NOS unused, some excellent used shape  

Grafton SpeedTraps Cleat Wear Tabs: Front & Rear Set (EXC)

Set of replacement wear tabs for your Grafton cleats! Comes with two front tabs and two rear tabs. Condition Excellent used shape. Some scratching but not much noticeable wear.  

Grafton SpeedTraps CLEATS! Missing Cleat Bolts/Washers (EXC)

Incomplete set of Grafton cleats. These have the wing protectors, cleat screws, and main cleats/wear tabs. Condition Excellent used shape  

NOS Grafton SpeedTraps CLEATS! MTB / Road / Cross - Wrenches & Hardware

Fresh set of cleats for 1990's Grafton pedals! I believe these are complete, see photos. Condition New old stock. Small cleat screws are still in factory bag  

Grafton Speed Traps CLEATS! MTB / Road / Cross - Older Version? (EXC)

These appear to be an older version of Grafton's SpeedTrap cleats? What I believe is the newer version have replaceable wear tabs front and rear, and don't use a plastic shim plate like these. If anyone has info on these two types of Grafton cleats and...

Ballistic Titanium Seatpost: 28.6mm x 150mm - For Display or Parts Only

Rare early 2000's titanium post that's tragically been cut too short to 150mm. Great for parts or display! Condition Cut to 150mm and should not be ridden unless you can have 4 inches of post inserted into your frame. Excellent cosmetic...

Shimano XTR SP-M900 Seatpost: 26.8mm - Black - Easton - Vintage 1990's

Fairly clean example of the 1st generation V1 XTR seatpost.  The M900 was this black ano (which wore off quickly), and the V2 was SP-M910 and silver (basically an XTR labeled Dura Ace SP-7410) Condition Excellent used shape with some of the usual...

NOS Suntour XC Pro SP-2000 Seatpost: 26.6mm x 330mm - Champagne/Silver - SP-XC00

This champagne/rose gold tinted seatpost was the sole XC Pro post in it's entire run from 1990 to 1994.  Easy to adjust two bolt micro-adjust clamp in silver. The previous XC Pro / XC 9000 post in the 1980's was the SP-XC00 which appears identical...

Syncros Hardcore Seatpost: 31.6mm x 330mm - Vintage 1990's - Black (Near Mint)

Great post for 1990's and early 2000's mountain bike builds!  They look great on road bikes too.  Their innovative microadjust clamp is still used today on high end bikes, notably Thomson. Low weight, easily adjusted 2 bolt clamp.  This is...

Syncros Hardcore Seatpost: 31.6mm x 330mm - Vintage 1990's - Black (Near Mint+)

Great post for 1990's and early 2000's mountain bike builds!  They look great on road bikes too.  Their innovative microadjust clamp is still used today on high end bikes, notably Thomson. Low weight, easily adjusted 2 bolt clamp.  This is...

Kool Stop V-Brake Pad Inserts: Green For Ceramic Rims (One Pair)

inserts cartridge v-brake pads to work on ceramic rims Condition New old stock in package Details Green One pair (for one brake)

Ritchey Logic Cantilever Brake Pads: Threaded Post - Black All-Weather (Pair, NEW)

One of the most iconic canti pads from the 1990! Condition New old stock in package Details Black all conditions One pair (for one brake)

Ritchey Logic Cantilever Brake Pads: Threaded Post - Red Extreme Conditions (Pair, NEW)

One of the most iconic canti pads from the 1990! Condition New old stock in package Details Red extreme conditions One pair (for one brake)

Ritchey Force Road Quill Stem: 1" - 95mm x 26mm - Silver (Near Mint)

This rare stem came stock on the early to mid 1990's Ritchey Road Logic and aftermarket.  It was the road version of the more common MTB Force stem.   Condition Near mint lightly used shape. Barely any wear Details 1" quill (22...

Salsa P10 DIRT DROP High Rise Quill Stem: 1" x 70mm x 26.0mm - 53 Degree - Black - Retro MTB (Near Mint)

The P7 (along with the 100mm P10) high rise stem is the iconic model that brought Jacquie Phelan and Charlie Cunningham's dirt drop craze (via the L.P. stem made famous on Jaquie's bike "Otto") to the mainstream.  Ross Shafer was the innovator, and...

Shimano XT FH-M730 x Saturne X32 Rim Brake 26" REAR Wheel: 32H x 130mm Uniglide (EXC++)

Mid 1980's touring / MTB rear wheel featuring the Uniglide XT FH-M730 laced to a Saturne X32 rim.    Saturne was Specialized's house rim brand, and all the rims were designed by Jim Merz.  Nobody seems to know exactly how...

Mavic XC 717 / XT HB-M760 Rim Brake 26" FRONT Wheel: 32H - Black (EXC+)

High end 26 inch front wheel from the early to mid 2000's. Shimano XT HB-M760 32 spoke laced to Mavic's top level rim brake XC race rims, the legendary XC717! Condition Excellent to near mint lightly used shape. Perfect bearings. Slightest brake pad...

Grafton SpeedLite Traps Road Pedals: Titanium - Clipless or Toe Clips - Silver

The SpeedTrap SpeedLites pedals are the same shape as the MTB Speed Traps, just in a slightly smaller body and without cage teeth. All versions of Grafton pedals use the same cleats.  Of course, you can remove the clipless hardware and run them with...

NOS 1990's Velocity Aerohead Rims: 700c x 28H - Gold Anodized - Semi-Aero - RARE (PAIR)

Early version of the classically styled Aero-Head rims straight out of Australia! These are an early version based on the decal, and in rare gold ano. These would be wonderful for a 1990's to early 2000's road bike restoration or any bike that a pop of...

Ringle Anti Chain Suck Thing: Silver Ano (Near Mint)

First released in 1991, the Ringle Anti-Chain Suck Thing was a mainstay on high end retro mtb's from the 1990's!  It was an effective and rad looking chain catcher, in a stark opposition to today's boring and/or ugly chain-catchers, and a way to add...

Shimano XTR ST-M950 8-speed Rapidfire Shifter / Brake Lever Combos (Near Mint)

Rare set of minty take off 8 speed XTR gunmetal grey shifters! The ST-M950 was made in 1996 and 1997, and in 1998 they released the ST-M951 (which was the same shifter but modified to work with the new SL-SS95 remote shifter). Condition Near mint...

Shimano XTR RD-M952 Rear Derailleur: Long Cage SGS (For Parts Only)

Worn M952 to use for parts or repair. Bulletproof long cage XTR rear mech from the mega 9 speed group.  Long cage to handle 11-34t cassettes. Condition For parts only. Slop in pivots, pulleys worn, good amount of cosmetic wear (though it does look...

Shimano XTR FD-M953 Front Derailleur: 28.6mm - Bottom Swing / Top Pull (Near Mint+ Barely Used)

The FD-M953 is the traditional bottom swing version from the famous M950/M952 group. This one is a 28.6mm clamp, for standard diameter steel frame tubing.  Great retro looking, but modern ultra high performance derailleur for your older style...

Suntour XC Pro Pedals: WTB Grease Guard - PL-XP01 - Black (Near Mint+)

Some of the most popular platform pedals of the 1990's mountain bike world!  These feature the ingenious WTB "Grease Guard", which is a grease port that allows you to lubricate the inner bearings via a grease gun without taking the pedal apart...

Salsa Cycles Moto Quill Road Stem: No Decal - 1" - 120mm x 26.0mm - 5D (Near Mint+)

1990's Salsa Moto, sans decals for a stealth theft-resistant look.  Perfect for your retro 1990's show bike restoration. Condition Near mint to mint lightly used shape.  Overall paint is glossy and clean with minimal scratching.  Gold...

Syncros Cattleprod Quill Stem: 1" x 160mm x 25.4mm x 0D- Silver - Retro 1990's MTB

Gorgeous mountain bike stem from the 1990's!  This is the same design as the Syncros Altura road bike stem, but with an ultra wide double bolt clamp instead of the Altura's single clamp.  A lot of CNC work went into these.  High quality,...

NIB/NOS Salsa Moto SUL Threadless Stem: 1 1/8" x 135mm x 25.4mm x 90D - Vintage 1990's - Removable Faceplate (Take-Off)

1st edition Salsa Mountain S.U.L. stem from the late 1990's and early 2000's, long before the recalled 2010 version (which was all black and had hash marks in the clamp area). Removeable face plate for easy bar installation.  Zero...