Velo Orange Switchable Dynamo Hub: 36H - SIlver (Near Mint+ Low Miles)

Shiny generator hub with the ability to switch off the drag created by the dynamo mechanism via a clutch switched by a 6-pronged knob. Condition Barely used. This hub shows just the tiniest signs of being laced. There's a scratched area on one outer...

NIB/NOS Alfredo Binda Leather Toe Straps: Red (MINT!)

Rare dark red color! They're more crimson than fire engine red.  Alfredo Binda toe straps are widely celebrated as the best straps money can buy.   Condition New old stock in paper bag.  These are among the cleanest Binda straps...

58cm Seven Tsunami Titanium CX/Gravel/Touring Frame: S&S Couplers - Wound Up Carbon Fork - Rack Mounts

Lovely 2001 Tsunami ti frame with couplers and rear rack eyelets/seatstay braze ons.  Seven marketed the Tsunami as a cyclocross frame and sold them with fully custom geometry/build quality.  This particular frame was built to be more...

Nitto RM-013 Dirt Drop Handlebars: 48cm x 26.0mm - Heat Treated (New but installed)

The Nitto RM013 is coined a "Dirt Drop" bar, though it's not like the WTB Dirt Drop you think of.  It's 7 degree flare is mostly at the ends/drops, leaving the hoods and hooks in a square/parallel position for nearly vertical brake levers and road...

Nitto RM-016N Moustache Handlebars: Heat Treated - 650mm x 26.0mm (New but Installed)

Heat treated RM016N moustache bars for your road/touring/townie/commuter/bar bike.  Perfect way to convert a vintage road bike with downtube shifters to an upright commuter bike. Condition New, but installed and reportedly never ridden. There is...

Prototype Sampson Stratics Titanium Bottom Bracket: Square Taper - 122.5mm (Near Mint+)

Sampson made some fine bottom brackets in the 1990's.  This is a prototype of the Stratics model circa late 1980's or very early 1990's.  It has a standard spindle type, the switch to the wildly shaped spindle center had not occurred yet...

Campagnolo Nuovo Record / GS Bar End Shifters: #1012/1013 - Blue Covers (EXC, Missing One Clamp Wedge)

1960's - 1980's Campy barcon shifters.  These have blue covers.  They were the only bar ends available in the era by Campy, so they came with any group that needed barcon shifters; Nuovo Record, Super Record, Gran Sport, Triomphe, Valentino.....

NOS Campagnolo #1034 Nuovo/Super Record Front Hub: Low Flange - 36H - Curved QR

Campy NR/SR Record hubs are a great starting point to build a bike around! In the 60's, 70's and 80's almost all decent bikes had these hubs, and for good reason.  They're great looking, and last forever with even less than optimal care.  This...

Alfredo Binda Extra Toe Straps: Drillium - Natural Leather & Red Fill - Custom? (NOS?)

Curious and cool set of Binda straps.  The leather is drilled down the center for lighter weight and rad looks, and each hole is filled with red.  The leather is unfinished natural leather. I'm not sure if this is from the factory or somebody...

Campagnolo Rally Long Cage Rear Derailleur: 1st Gen V2 - #3450 (Near Mint+)

This is a 1st generation Rally long cage derailleur, of the 2nd type which has a reinforced neck to address the cracking issues the 1975 Rally RD had.  A favorite of touring cyclists who run a triple crank, as it's the prettiest and most reliable...

NIB/NOS Silca Impero Frame Pump & Head: 45.5cm Full / 32.5cm Body - Black

Fresh Silca Impero with head in black.  Condition New old stock in retail packaging!  Hardly any shop wear.  The last one purchased does not have a package Details Body: 32.5cm  Total length to head end at saddles: 45.5cm...

NIB/NOS Silca Impero Frame Pump & Head: 46cm Full / 33cm Body - Silver

Fresh Silca Impero with head in silver.  Condition New old stock in retail packaging!  Hardly any shop wear.  The last one purchased does not have a package Details Body: 33.5cm  Total length to head end at saddles: 46cm...

NIB/NOS Belleri BF Randonneur Handlebars: 42cm - 1960's 1970's - Rare

Rare randonneuse / touring bars from Belleri (also spelled Belri) of St. Etienne, France circa 1960's and 1970's.  These feature flats with a rise from the clamp for increased hand comfort, typical of randonneuring handlebars.  These have a...

NOS British Ribbed Brake Cable Housing: White - 40s/50s/60s (Per Foot)

This lovely cream white housing was very popular on classic English lightweight road bikes, muscle bikes, and cruisers.  It is possibly made by Raleigh or Phillips, maybe even Sturmey Archer. It features a lengthwise ribbed design, and is...

NIB/NOS Minoura Mira Alloy Toe Clips: Gold Small (Sold in Pairs)

Lightweight Japanese toe clips from the 1980's and early 1990's Condition New old stock in retail packaging, with mounting hardware Details Size: Small Gold Aluminum

NOS Christophe D 496 Toe Clips: Small- Chrome (Sold in Pairs)

Christophe "D" clips are just a size designation to their standard 496 toe clip.  The horizontal logo was placed on the size small clips because there wasn't room for the vertical logos, just like the "Special" designation was only used on Large /...

NOS Vega Toe Clips: Large - Spain - Chrome - 46g (Sold in Pairs)

Cool Spanish toe clips, likely 1960's or 1970's based on the style of the oval Made in Spain bottom marking. These have unique little protruding ridges on the forward arms and a minimalistic style of toe strap loop. When you think Spain and vintage...

NOS Drillium Toe Clips: Large - Super Sport Italy-Superlight 56g/pair - Chrome (Sold in Pairs)

Tired of the same old Christophe/Zefal/MKS/Campagnolo clips? Get something truly unique! I have not found any information on these clips, labeled Super Sport Italy.  They are factory drilled on the uprights, through the toe strap loop, and the...

NOS Milremo Campionissimo Christophe Toe Clips: Medium - Chrome (Sold in Pairs)

Are you tired of the same Christophe, Zefal, and Campagnolo toe clips EVERYONE is riding? These are Christophe 496 toe clips rebranded for British importer/distributor Milremo, and they're your inexpensive way to be different on your next L'Eroica ride...

NOS Alfredo Binda Toe Straps: Dark Blue - Bianchi-Dino (Residue in spots)

Alfredo Binda toe straps are widely celebrated as the best straps money can buy. They're known to be long lasting, comfortable, and classy.  Condition New old stock, Never installed. Leather is overall nice but has some weird residue from...

1st Gen Shimano Dura Ace L-600 Fingertip Touch Bar End Shifters: 1970's - BLACK! Friction (EXC)

1st gen Dura Ace bar end shifters from the 1970's.  These are not retro-friction, but employ a spring mechanism to create a very light feel in both directions.  Retrogrouch explains it as "The spring in the rear derailleur is typically "high...

NIB/NOS Shimano 600 1st Gen 3 Bolt Chainring for GC-100: 40t Inner

Rare 3 bolt chainring from the 1st generation Shimano 600 GC-100 crankset which ran from 1975-1977 Condition New old stock in retail package Details 40 tooth Silver

NIB/NOS Shimano 600 1st Gen 3 Bolt Chainring for GC-100: 42t Inner

Rare 3 bolt chainring from the 1st generation Shimano 600 GC-100 crankset which ran from 1975-1977 Condition New old stock in retail package Details 42 tooth Silver

NIB/NOS Shimano 600 1st Gen 3 Bolt Chainring for GC-100: 52t

Rare 3 bolt chainring from the 1st generation Shimano 600 GC-100 crankset which ran from 1975-1977 Condition New old stock in retail package Details 52 tooth Silver

MAFAC 2000 Competition Brake Levers: Full Black Hoods - Blade Covers (EXC)

This set of Mafac levers comes with full black hoods and large adjusters, making them 2000 Competition levers Mafac Racing levers fit both half hoods (Course model) and full hoods (2000 model), this set has full hoods.  The model of these is...

NOS MAFAC Course / 2000 Brake Levers w/ 1 Brown Full Hood

This set of Mafac levers comes with one pristine full hood in brown with barrel adjuster and barrel adjuster cover! Racing levers to fit both half hoods (Course model) and full hoods (2000 model).  The model of these is determined by the hood and...

NIB/NOS MAFAC Racing Brake Levers: Twin Cable Tandem + Standard - For Half or Full Hood (Pair)

This is a lever set consisting of one twin cable lever and one standard single cable lever.  The twin cable lever is designed to control two brakes from one lever, and was marketed to tandem bikes (particularly when running both a drum brake and rim...

NIB/NOS MAFAC Course / 2000 Brake Levers: For Half or Full Hood (Pair)

Racing levers to fit both half hoods (Course model) and full hoods (2000 model).  The model of these is determined by the hood and the barrel adjuster.   Condition: New old stock in oem bag with model tag.  Pristine. First set...

Mafac Tiger Centerpull Brakeset: RARE! 1960 - Carriers/Stops (Near Mint+ Low Miles)

Beyond rare set of clean Mafac Tigers!  The Tiger model was introduced in the very late 1950's as an upgrade to the Racer. It's arms were spaced further apart for more leverage (and greater tire clearance?).  The radical brake pad attachment...

NOS Suntour Barcon Bar End Shifter Jam Nut: Chrome (Sold Individually)

I've lost count of how many bar end shifters I've acquired missing their outer jam nuts! I only have a few, grab one while you can! Condition New old stock. If you buy my remaining stock you can have the OEM card and bag Details Sold individually...

Early Specialties TA Pro 5 Vis Crankset: 170mm x 52/40T Capped Pedal Holes - French (Near Mint+ Low Miles)

Very clean early version that features the closed pedal holes, with the little "cap" with a hole in it over the back sides.  The very earliest versions had different flutes and little engraved logos near the dust caps, and these were after those...

Stronglight 63 SC Super Competition Crankset: 170mm x 52/45t - French (NEAR MINT+)

The rare Stronglight model 63 SC (Super Competition) was introduced in 1963 as an update to the 57 SC, their top of the line racing model. It's arm profile and double taper is similar to the 49D, but the SC line uses a star shaped 122mm integrated spider...

NOS Campagnolo Shifter Rubber Covers: British Racing Green - (pair, discoloration)

Rare set of British Racing Green colored covers for Campy Record & Gran Sport bar end shifters, downtube shifters, and quick release lever blades. Condition New old stock, but oddly the color is kind of mottled in spots.  Rubber is supple, and...

Suntour GT RD-1200 Rear Derailleur: Long Cage - Touring (MINT+ Low Miles)

The Suntour GT from the 1970's was a super smooth shifting derailleur with capability to shift up to 34t cogs and 36t total capacity.  It wasn't sleek looking nor lightweight, but it sure did shift well.  Better than the mighty Cyclone GT...

Paul Cross Lever: Right - 26.0mm - Inline/Interrupter (Near Mint+)

The Paul Cross Lever is designed to be run on it's on for on the tops road drop bar setup, or as an inline lever secondary to a standard road lever.  They work with both short and long pull brakes (v-brake, cantilever, mechanical disc)...

Paul Cross Lever: Left - Black/Silver - 31.8mm w/ 26.0mm Shim- Inline/Interrupter (Near Mint+)

The Paul Cross Lever is designed to be run on it's on for on the tops road drop bar setup, or as an inline lever secondary to a standard road lever.  They work with both short and long pull brakes (v-brake, cantilever, mechanical disc)...

Cyclo Benelux Super 60 Rear Derailleur: 1st Type (Near Mint+ Low Miles)

Introduced in 1960, the Super 60 was Cyclo-Benelux's attempt at competing with Campagnolo and it's Gran Sport + Record drivetrains.  It was the companies first dual parallelogram derailleur, and was designed to be a top level racing model.  The...

NIB/NOS TO Shimano W-Cut Chainring: 52t x 130mm - Dura Ace & 600 EX / AX

This chainring came on the high end Shimano cranks from about 1979 to 1984.  They were on the Dura Ace AX FC-7300, FC-7110, EX FC-7200, plus Shimano 600 EX Arabesque FC-6200 and EX FC-6300. Condition New old stock in retail package, though the...

NIB/NOS Suntour Alpha 6-Speed Freewheel: 13-28t - 4 Prong - Road/Touring/MTB

The Alpha was a mid level FW from the mid to late 1980's.  It uses the same 4 prong remover as the Winner Pro.  The somewhat wide range makes it suitable for touring bikes, and early mountain bikes. Condition New Old Stock in retail box,...

Paul Cross Lever: Left - Black - 31.8mm - Inline/Interrupter (Near Mint)

The Paul Cross Lever is designed to be run on it's on for on the tops road drop bar setup, or as an inline lever secondary to a standard road lever.  They work with both short and long pull brakes (v-brake, cantilever, mechanical...

ENVE AR Fork Fender & Stay: Clip On (New?)

This is a front fender specifically for the ENVE All Road carbon fork. It clips directly onto the fork's special attachments.  The fender and strut are typically sold separate, with a combined MSRP of $215 Condition Appears unused.  A few...

Campagnolo Nuovo Record / GS Bar End Shifters: #1012/1013 - Blue Covers (EXC)

Clean example of 1960's - 1980's Campy barcon shifters.  These have blue covers.  They were the only bar ends available in the era by Campy, so they came with any group that needed barcon shifters; Nuovo Record, Super Record, Gran Sport,...

NOS Silca Impero Pump Sleeve: Silver

OEM replacement sleeve that fits under your Silca Impero's pump head.  Fits all Impero frame pumps and likely some other pumps. Condition New old stock, some have very minor shop wear Details Silver/chrome