COMPONENTS

1st Gen Campagnolo " No Record" Nuovo Record Strada High Flange REAR Hub: 36H x 126mm (EXC Perfect Bearings)

This is a first generation "Nuovo" Record rear hub! It was made from 1960 to 1963, and is just like the later and more common NR hubs, but lacks the word "RECORD" under the Campy "World" logo.  These are quite rare, and a must if you have an Italian...

NOS Bottle Cage / Fender / Rack Bolts: Thin Hex Head - Chrome - 5m (Pair)

Hard to source steel hex head bolts for your water bottle cages, mudguard & rack attachment to eyelets, extra long toe clip bolts, or a variety of other uses that take M5 bolts.  Great for your L'Eroica bikes or vintage road bike restoration...

NOS Zeus Bottle Cage / Fender / Rack Bolts: Chrome Hex Head - 5m (Pair)

Hard to source steel hex head bolts for your water bottle cages, mudguard & rack attachment to eyelets, extra long toe clip bolts, or a variety of other uses that take M5 bolts.  Great for your L'Eroica bikes or vintage road bike restoration...

NOS Zeus Toe Clip / Cable Cinch Bolts: Chrome Hex Head - 9mm Shaft (Pair)

Chromed hex head bolts for toe clips, derailleur cable bolts, etc. Condition New old stock Details Pair Chrome steel Shaft length: 9mm  

NOS Zeus 2000 / Criterium Brake Lever Bodies: (Pair)

Replacement brake lever bodies from 2000 and Criterium levers.  Condition Likely new old stock with shop wear though these could have been used. Details Sold in pairs

NOS Zeus Criterium Brake Lever Blades & Pivots (Pair)

Replacement lever blades from Criterium levers.  Condition New old stock, light shop wear Details Sold in pairs

NOS Zeus Brake Parts LOT: New Racer / Criterium - Arms Springs Hardware...

Handful of spare arms and hardware from Zeus New Racer (and other) brakes. The top two brakes are complete minus pads and barrel adjusters Condition New old stock mostly. Details

NIB/NOS Zeus New Racer Brakeset: Nutted - 55/40mm Standard Reach - Silver

Very rare mid level brakeset from the early to mid 1980s from Spanish component maker Zeus. This is what I believe to be the earlier version that says "Zeus" on the arms vs later ones that say "New Racer". These have nice chrome hardware and unique...

Modolo Professional Brake Levers: Gold - 1st Gen 1970's - Gum Hoods - Inter Pat (Near Mint+ LOW MILES)

Very early example of the Modolo Professional levers in gold anodizing. These have the early Modolo gum hoods that were used before the 919 Anatomic hoods released in 1982. They also oddly had lever blade top decals instead of engraved for the diagonal...

ENVE Carbon Seatpost: 30.9mm x 400mm - Zero Offset (Barely Used Mint)

Super lightweight, stiff, and dampening post from ENVE! Condition Just barely used, no real wear to note. Details Diameter: 30.9mm Length: 400mm Setback: 0mm Black Weight: 204g MSRP: $300

Gorilla Brake Beefer Booster: Black Ano - Vintage 1990's - Made in Durango (EXC+)

Rare Gorilla brake booster for cantilever brakes, made in Durango Colorado. Condition Excellent or better lightly used shape. Not faded, just light ano wear

YETI Step Down Ferrules For ARC, ARC-AS, FRO, ULTIMATE (Sold Individually)

Original step down brake cable housing ferrules for Yeti Pro Fro, ARC, ARC-AS, and Ultimate from the 1990's. Condition Average used shape with cosmetic wear. Details Sold individually

NOS Look Dynamic Memory Eyelet Tool for Delta Cleats

This tool is used for the screw in the fourth center hole in some LOOK delta cleats. Condition New Details Red

NIB/NOS Campagnolo Pedal Toe Flip Kick Tabs & #767 Toe Clip Bolts (Pair)

Pair of toe clip bolts and pedal flips.  These attach to your Record SL or Gran Sport (and many other makes/models) pedals and allow you to flip the pedal over with your foot easier.   Condition New old stock in package, factory...

DIA-COMPE New Gran Compe NGC-202 Brake Levers: Champagne Ano! Dual-slotted - Non-aero

The NGC202 was DIA-COMPE's top of the line non-aero brake lever in the 1980's. These have two rows of slanted slots milled into each blade, the "GC" logo engraved at top, and a cutout on the sides. This pair is special as it's anodized a bronze /...

Campagnolo Nuovo Record Brake Levers: #2030 - NOS GUM Hoods (Near Mint+)

3rd generation NR levers from ~1978-1985. This is the only generation with the shorter reach levers. Brev Camp in pivots Comes with a set of mismatched Shield logo gum hoods, tan and brown. Condition Near mint or better lightly used shape levers plus...

Campagnolo Nuovo Record Brake Levers: 1st Gen #2030 - NOS GUM Hoods (Near Mint

Rare set of first gen NR levers, identified by the round hole on the back of the blades vs the later (and MUCH more common) lever's "U" shaped opening.  The lever blade is also slightly different, with a bit more bend producing a LONG reach and a...

Campagnolo Super Record Brake Levers: #4062 - White Original Hoods (Mint LOW MILES

Drillium Super Record levers from their third generation circa 1984 to 1987. These are identified by their white hoods, no markings in lever pivots, and shield logo clamps. Condition These are so clean I almost thought they were NOS. They're mint with...

Campagnolo Super Record V2 Rear Brake: #4061 - Standard Reach (Near Mint+ Low Miles)

Show worthy example! The gold standard for brakes on 1980's Italian road bikes!  These are the 2nd version of the SR brakes circa 1983-1987, with the script logo and alloy tire guides dipped in rubber.  Condition: Near mint or better with...

SEVEN Cycles Titanium Threadless Stem: 1 1/8" x 110mm x 26.0mm - Vintage 1990's (Near Mint+)

1990's or early 2000's ti stem from SEVEN out of Somerville Massachutsets.  This early version features a single bolt bar clamp, replaced in later years with a removable faceplate.   Condition Near mint lightly used shape.  Pretty...

Chris King Inset 8 Headset: Black - 1 1/8" > 1 1/4" Tapered - 44mm (Perfect Bearings)

Built for the next generation of tapered road forks the Chris King InSet™ 8 is built to fit contemporary road and cross bikes that utilize 1-1/8” to 1-1/4”tapered steerer tubes and a 44mm headtube. Our InSet™ 8 combines our...

Chris King 1 1/8" NoThreadSet Threadless Headset: Sotto Voce Red (Near Mint+ LOW Miles)

Nice CK headset for your 1 1/8" fork.   Condition: Near mint to mint barely used shape with very low miles. Only a couple tiny marks in the ano. Details: Size: 1 1/8 inch threadless Color: Red Sotto Voce Includes baseplate MSRP: $207

Chris King 1 1/8" NoThreadSet Threadless Headset: Sotto Voce Black (Near Mint+ LOW Miles)

Nice CK headset for your 1 1/8" fork.   Condition: Near mint to mint barely used shape with very low miles. Only a couple tiny marks in the ano. Details: Size: 1 1/8 inch threadless Color: Black Sotto Voce Includes baseplate MSRP:...

Dropper Post Remote: Black - 2X Setups Right or Left Side (Near Mint+)

Slim mount dropper lever that works with your double setups! Condition Near mint to mint barely used Details For left or right mount

Ergon SMC Men Saddle: Med/Lg (New take-off)

The ERGON SMC saddle provides a wide flat surface to support your sitbones and a generous cutout for your sensitive bits. it takes the idea of a wide, flat, and short saddle from the Specialized Power, and makes it even flatter for  more support...

Campagnolo Super Record 2-Bolt Fluted Seatpost: 1st Gen 1970's! - 26.0mm - Alloy Ears (Near Mint+ Low Miles)

This is a genuine 1st generation Super Record seatpost from 1973-1978.  It is distinguished from the much more common Nuovo Record two-pin seatpost with it's factory flutes, alloy clamp side ears, hollow center pin, tapered top of polished section,...

NOS Campagnolo Super Record 50th Anniversary Toe Clips: Medium - Alloy - High Polish

Rare toe clips issued with the 1983 Campagnolo Super Record 50th Anniversary gruppo. These are identical to standard Super Record aluminum toe clips except they have a slightly finer polish and the Campy shield logo is replaced with the dual-shield 50th...

Time Equipe Titan Magnesium Pedals: Vintage 1990's - Grey (Barely Used Near Mint+)

Top level racing clipless pedals from the 90's! These were ridden to Tour De France victory by several legends including Marco Pantani, Jan Ullrich, Migel Indurain, Pedro Delgado and Greg Lemond.  Condition Very very few miles ridden! The top...

Shimano Dura Ace PD-7401 Clipless Pedals: Grey (R: Low Miles Perf Bearings, L: Average)

First Dura Ace pedals circa mid 1980's, from the 7400 groupset.  These use Shimano or Look Delta cleats. Condition The right pedal is excellent or better with perfect bearings. The left is more worn and I'm throwing it in as a free bonus. These...

Maxxis High Roller II 26 x 2.3" Tire: EXO - TR (<100 Miles)

Solid All-Mountain or heavy duty XC/trail race tire from Maxxis.  Tubeless ready.  These tires have oodles of grip and great durability. Condition Just barely used, less than 100 miles. Some dirt, hardly any wear. Details Size: 26" x 2...

Specialized S2 Quill Stem: 100mm x 25.4mm - Made by Nitto - Silver (Near Mint)

These are hard to come by in the box.  This is the S-2 model, made by Nitto. It's a late 1980's or early 1990's version (date code 1991). This era had the wedge expander vs the earlier cone. It's a beautiful stem, with sultry curves and a satiny...

Thomson Elite Seatpost: 30.6mm x 367mm - Black (Near Mint+ Low Miles)

The Thomson Elite is one of the stiffest and strongest posts made, and looks bomb.  Condition Near mint or better with low miles. Hardly a mark. Details 30.6mm Length: 367mm Setback: Zero Part number: SP-E160 MSRP: $122  

Shimano Pro Vibe Carbon 3K Seatpost: 31.6mm x 400mm - Black (Near Mint+)

High end carbon post with a 2-bolt micro adjust clamp from Shimano. Condition Near mint or better lightly used shape. Mostly just insertion measurement decal wear and faint insertion marks. Details 31.6mm Length: 400mm Black

Fi'zi:k Arione CX Saddle: K:ium Rails - Black (NEW, Take-Off)

Discontinued and much loved cyclocross-specific version of the base Arione! It features the same shape, with a lighter and firmer padding to better withstand the rough conditions of cx racing. Black leather, with a glossy black strip down the center...

Selle Italia Flite Trans Am Gel Flow Saddle: Cutout -

Very popular saddle from Italian saddle maker Selle Italia, circa early 2000's. The "Trans Am" designator in the model name means there is a cutout. This was the first Flite saddle with a cutout. Condition Very good to great use shape.  Overall it...

Selle Italia Flite Titanium Genuine Gel: Perforated Black Leather - 2003 (Near Mint)

Rare version of the venerable Flite Titanium, with perforated leather panels from the early 2000's.This one of my fav's, it's a neat blacked-out aesthetic. Condition Near mint lightly used shape. No holes/tears/scuffs. Only real wear to note is weird...

Moots Titanium Quill Stem: 1 1/8" x 140mm x 25.4mm - RARE Vintage 1990's (EXC+)

Super rare quill stem from Moots, circa early 1990's or very late 1980's. Moots threadless stems are everywhere, but their quill ti stems are rarely seen. You even see their steel Mountaineer stems more often! Perfect for your Moots YBB, Rigor Mortis,...

TRP TR25 Centerlock Rotor: 160mm Two Piece (New, Installed on Hub)

TRP’s two-piece rotors offer superior heat dissipation due to the aluminum center as well as excellent stiffness to provide you with confidence in your braking and lighter weight.  Two-piece is now combined with TRP’s new slotted rotor...

TRP TR43 6-Bolt Rotor: 160mm Two Piece (New, Installed on Hub)

TRP’s two-piece rotors offer superior heat dissipation due to the aluminum center as well as excellent stiffness to provide you with confidence in your braking and lighter weight.  Two-piece is now combined with TRP’s new slotted rotor...

NIB/NOS (Unica) Nitor Mod. 63 Seatpost: 27.2mm - Red Synthetic Friction Plates - 1960's / 1970's

The Nitor - Unica model 63 seatpost was released in 1963 and ran into the 70's.  It was a very expensive upgrade to the Campagnolo Nuovo Record 2-pin seatpost that was the gold standard of that era. These were only ever marked Nitor, which was...

Cinelli XA Quill Stem: 125mm x 26.4mm - Silver (Barely Used Near Mint+)

Cinelli's aero styled alloy quill stem, circa 1980's to mid 1990's.  Condition Mint barely used shape, not much more than a few light marks on the clamp Details 125mm 26.4mm Silver Black shim

Antique Seatpost Binder Bolt/Nut + Cable Hanger Stop: Steel

Very old cable hanger and binder bolt set, unknown origins.  Condition Average used shape with finish wear and light rust  

Shimano Right SPD-SL Pedal Axle: #43298010 (NEW)

Replacement OEM spindle for your Shimano clipless pedals. I THINK this is for SPD-SL pedals, but I'm not certain. Do your research on this with the model number, or gamble the half of retail $10 Condition New in sealed package

Control Tech Stix Stumpy Bar Ends: Short Stubby Version - Vintage 1990's - Black (Near Mint+)

Rare short and stubby version of Control Tech's 1990's bar ends, officially named the Control Stix Stumpy. Condition Near mint or better with very few miles. Only a few very minor marks. Details Black

Galfer Wave 180mm Disc Rotor: 6-Bolt (Very Low Miles)

Bargain price on a barely used six bolt rotor. Condition When I photographed these I thought it was a new take-off with hardly a sign of pads touching it, but in the pics they look slightly more used than that. Very low miles either...

Easton Havoc 35 Direct Mount Stem: 45mm / 50mm x 35mm - Black

Bargain priced bolt on / direct mount stem for 35mm bar clamp. Adjustable length Condition Average used shape with some cosmetic wear

BMX Parts Lot: 4 Pegs + Right Odyssey Brake Lever + Spank Grips + Title Gyro + Race Face Ride 31.6mm Seatpost

Bargain basement price on a pile of modern BMX parts Condition Average to great used shape, see pics. Sold AS-IS Details Seatpost: 31.6mm x 165mm

EXT Spring Coil: 140 x 350mm (Near Mint+ Barely Used)

High end coil from EXT Condition Near mint or better barely used shape. Very minimal miles and marks Details 140x350mm