Misc Hardware

MKS NJS Chain Tensioners: 5mm Dropout (Pair, NEW)

These are designed for horizontal dropouts to tension your chain.  This is the allen head version Condition New in package Details Pair Model: CA-MKS Fits dropouts up to 5mm thick Fits axles up to 10mm diameter 3mm allen bolt

Early Lyotard Ref 669 Dust Cap: 1930's / 1940's - Knurled Edge Flat Head Slot - Course 460 / 240

This is a dust cap for the first gen Lyotard pedals from the 1930's and 1940's.  VERY scarce piece of Lyotard history. Condition Plenty of patina and tool wear to match the average patina on pedals this old, but perfectly usable.  Inside is...

NOS/NIB Campagnolo Nuovo Record & SL Strada/Pista Pedal Race Set (2 Races)

One pair of inserted races for one pedal (each pedal needs two races). These fit Nuovo Record & Superleggera pedals, both road and track.  Super Record uses the same size races, but made of titanium Condition New in...

NOS(?) REG #376 Umbrella Clip / Frame Pump Mount: Chrome - No Bolt

Classy alternative to the Campagnolo #632 to hang your Silica Impero or other frame pump on your classic bicycle!  This one is the clover design cutout, without the reinforcement ring that was introduced with the CPSC in 1978 Condition Appears new...

NOS Teledyne Titan Seatpost Binder Bolt: RARE! - Chrome

Is your 1970's titanium Teledyne Titan frame missing it's unique post binder bolt?  This is the original in NOS condition! It will work just fine for other frames as long as the width is right.   Its a great alternative to the Campagnolo...

NOS Ideale #2 Saddle Clip / Seat Clamp: Chrome Plated - Standard Width 38mm

Clean and complete saddle clip for your Ideale saddle, or any other saddle with standard width rails.  This one has its original thin nuts! Condition New old stock, minor shop wear.  One nut has a few spots of rust.  

NOS Shimano Dura Ace 7600 NJS Track Cog Lockring: Black

Original pista track cog lockring from the Dura Ace 7400 group.  NJS stamped. Condition New old stock Details Black Threads: English

Fabric Stratosphere Pro Floor Pump Replacement/Upgrade Parts: Braided Hose w/Head - Wooden Handle & Base - Gauge - Shaft

Replacement parts lot for your premium Stratosphere Pro, or upgrade parts to make your Stratosphere a Pro!  This appears to be most of a complete pump, but the shaft is oddly too short.  I acquired all this from a shop buyout, I am unsure...

NOS Campagnolo #646 Rubber Seal Washer For Silca Impero Frame Pump Head

This is the rubber seal that goes under any pump head on Silca Impero frame pumps.  It will work with many other frame pumps as well. Condition New old stock Details Sold individually

NOS Campagnolo Nuovo/Super Record Barrel Adjusters: PAIR - Black O-Rings - Fits All Vintage Campy Brakes

Untouched set of original Campagnolo barrel adjusters!  These were original equipment with Super Record, Nuovo Record, 50th, and Cobalto brakes.  They will fit many other models, listed below.  They even fit Suntour Superbe...

Shimano Dura Ace Downtube Cable Right/Rear Stop: STI + Bar End Barrel Adjuster: SM-CT74 - FLAT - Bolt (Single, New)

This adapter bolts onto your vintage bike's downtube braze on mounts, and act as cable stops for STI, Ergo, and bar end shifters.  This is the version with housings that are flat, to fit your alloy and carbon frames.  Includes stainless steel...

NOS DIA COMPE / Weinmann Step Down Brake Lever Ferrules: Road / BMX / Flat Bar (Sold in Pairs)

These ferrules fit in the top of non-aero road brake levers, as well as for flat bar bmx and city brake levers.  They came with DIA COMPE, Gran COMPE, Gipiemme, Weinmann, and similar levers.  They work with most levers that don't have threaded...

NOS Marcel Torino Wing-Nuts: Brass + Chrome - 5/16" Axle (Sold In Pairs)

Before Tullio Campagnolo invented quick releases in 1927, the best method of wheel attachment was the axle wing nut.  They provide a tool-free installation and removal, vs traditional axle nuts which require a wrench.  Today, they are loved by...

Middleburn R01 Triple Road Crank Spider: 104/64mm - 44mm Chainline (NEW)

This 4 bolt, 104mm BCD is designed for triple and double on the Middleburn R01 crank arms (and probably Middleburn's other crank arms, they're all the same interface.  The difference seems to be the chainline the spider produces on a given crank...

NOS Huret Luxe Wing Nuts: Chromed Brass - 5/16" For Front Hub Axle (Sold In Pairs)

Before Tullio Campagnolo invented quick releases in 1927, the best method of wheel attachment was the axle wing nut.  They provide a tool-free installation and removal, vs traditional axle nuts which require a wrench.  Today, they are loved by...

Frank Spivey(?) Long Cage For Campagnolo Nuovo Record: Drillium - Bullseye Pulleys - 123mm c-c - Cupertino/Spence Wolf (Near Mint+)

This custom extra long cage quite likely came out of Frank Spivey's workshop, alongside the better known yet ultra rare Spence Wolf Alpine.  This one is even longer, at 123mm center to center on the pulley bolts!  The cage consists of two...

Shimano Ultegra 11s ST-6800 STI Name Plate & Fixing Screw: FRONT/LEFT - Y00F98020

OEM replacement faceplate for Ultegra 11s shifters from the 6800 group.  Includes fixing screws. Condition New in factory sealed package Details Includes (one) faceplate and (two) fixing screws. Left hand

LEFT Campagnolo Chorus Ergo Downtube Shifter Cable Barrel Adjuster / Adapter: Black - (NEW)

 Out of production and not available anywhere else in this black version!  These cable barrel adjusters bolt on to your frame's downtube shifter boss's, and allow the use of Ergopower, STI, or bar-end shifters.  MUCH nicer than the Shimano...

NIB/NOS TA REF. 83 DOUBLE Chainring Coupling bolt set : Pro 3 Attaches / Pro 5 VIS - (3) bushed nut, washer, screw

Set single ring chainring bolts to couple your two chainrings on a Specialties T.A. Pro 3 Attaches crank.  These are also the exact same bolts used by the Pro 5 Vis (REF 64), just in a 3 pack.  You'll need two packs of these for their 6 bolt...

Maxis Modular Valve System (MVS) Stems: 48mm - Sold in Pairs

The Maxxis Modular Valve System allows you to easily customize your bike. The separation of the tube and valve stem allows you to choose your valve length without having to deal with finicky valve extensions. When the tube eventually needs to be...

Barrel Adjuster O-Rings: Campagnolo / Suntour / Dura Ace - White/Red/Blue/Green

Did your Campy brake's barrel adjuster o-rings dry rot into oblivion?  These are your solution!  They're inexpensive, fit perfectly, and come in several colors.  The red is very similar (to the red found on Suntour Superbe brakes). ...

Honjo M79 Fender Stays: 58mm Wide for 650B -Pair (NEW)

Pair of fender stays for Honjo H79 fenders. Condition  New in package Details  Sold in pairs. No hardware

Rene Herse Light Mounting Bolt Kit (NEW)

This is designed for Rene Herse, Compass, and most Nitto racks with integrated light mounts.  It will likely work for other racks too.  The attachment includes a locknut, so you can adjust the beam angle by hand, yet the light...

Honjo 6mm Crown Daruma Eyelet Bolt: 17mm (NEW)

Mounts in the hole on the bottom of your fork crown Condition New in package Details  Length: 17mm

Honjo H79 Sliding Bracket: For 58mm Turtle (NEW)

This sliding bracket is used to mount the rear fenders on bikes where the seatstay bridge is not drilled at the bottom for direct fender mounting.  This one is for 58mm wide fenders to fit 650b x 42 tires or 26" rat trap pass tires.  Fits...

Nitto / Sim Works 120mm Straight Connection Rod For Racks: Black (Pair, NEW)

Nitto made rack to frame connecting rods. Condition New in retail package Details 120mm, straight

DIA-COMPE 1242 Straddle Cable Carriers / Hangers: BLACK (Pair, NEW)

Hard to find black version of the B1242 cable carriers. Condition New old stock Details Sold in pairs Black

NIB/NOS Shimano Derailleur Cable Anchor Bolt, Nut, & Washer: #5419901

This is an OEM cable fixing anchor bolt assembly for a variety of rear derailleurs.  This style of bolt was very common on mid and low end derailleurs in the 1980's, but they were found on other age and high end derailleurs as well.  The bolt...

NIB/NOS TA Pro 3 Attaches Pista Chainring Bolt Set: REF P23 - Single Ring

Set single ring chainring bolts for TA 3 arm cranks. Condition New in package, pristine  

NOS Shimano XT 4-Finger Brake Lever Rubber Dust Boots / Hoods: BL-M700 Deerhead / BL-M730 / BL-M732 (pair)

These rubber covers came stock on 3 and 4 finger brake levers from the early to mid 1980's.  Condition New old stock, no package. Supple Details One pair (two boots)

Jagwire Mini Inline Adjusters: Black (pair, New)

These little barrel adjusters are installed on your brake cable housing run near the shifters, and allow for quick adjustments to your derailleurs.   Condition New, though a few have light marks from shop wear. Details Black Pair

NOS Vintage Gipiemme Seatpost Binder Bolt / Pin: Outer Bolt Only - Chrome (rare!)

Italian made Campagnolo clone from the 1970's to mid 1980's!  Engraved/pantograph Gipiemme logo on head.  Quite rare.  This is only the threaded bolt, you will have to source your own nut. Fits a standard Campy, Sugino, or otherwise...

Blackburn Front Pannier Rack Mounting Extension Arm: To Crown

This is an extension arm that connects your front rack to your fork crown (via brake bolt) Condition New.  Details Length: ~4 3/4"

Christophe Toe Clip Mounting Hardware: Plates & Bolts (NIB/NOS Pair)

High quality OEM toe clip mounting hardware that comes with Christophe toe clips.  Included is a two mounting plates that go between the toe clip and the pedal cage, four mounting bolts and nuts. Enough for one set of pedals, works with all standard...

NOS Suntour Quick-Band Seatpost Binder QR Clamp: For Lawwill Pro Cruiser - 28.6mm - #1091 - "Quick Pattern" (STUPID RARE!)

Every now and then, you come across that unicorn holy grail part, and this is one of those times! This is a mid 70's to about 1982 Suntour "Quick Band" quick release seat post clamp, that came stock on ~1978 to 1982 Mert Lawwill-Knight Pro Cruiser. ...

NOS DIA-COMPE Bakelite Caliper Brake Bolt Caps (Pair): Dark Grey - BMX Nippon/MX - Threaded

These caps thread onto the back of the caliper mount bolt, outside of the nut.  They essentially cover the section of exposed threads outside of the nut.  They work for ALL nutted caliper and centerpull brakes that have a bit of thread outside...

Set of 6 NOS DIA-COMPE Bakelite Caliper Brake Bolt Caps: Dark Grey - BMX Nippon/MX - Threaded

These caps thread onto the back of the caliper mount bolt, outside of the nut.  They essentially cover the section of exposed threads outside of the nut.  They work for ALL nutted caliper and centerpull brakes that have a bit of thread outside...

NOS DIA-COMPE Bakelite Caliper Brake Bolt Caps (Pair): "D-C" - BMX Nippon/MX - Threaded

These caps thread onto the back of the caliper mount bolt, outside of the nut.  They essentially cover the section of exposed threads outside of the nut.  They work for ALL nutted caliper and centerpull brakes that have a bit of thread outside...

Set of 6 NOS DIA-COMPE Bakelite Caliper Brake Bolt Caps: "D-C" - BMX Nippon/MX - Threaded

These caps thread onto the back of the caliper mount bolt, outside of the nut.  They essentially cover the section of exposed threads outside of the nut.  They work for ALL nutted caliper and centerpull brakes that have a bit of thread outside...

Shimano 10 Speed Chain Pins: 5 Pack - Dura Ace/Ultegra/Tiagra/XTR/XT/SLX...

These chain connecting pins fit all Shimano 10sp chains, including Dura Ace cn-7800, Ultegra, Tiagra, Sora, XTR, XT, SLX, Deore.   The one exception is these do NOT fit Dura Ace 7900 chains, which have their own pin. *This is a pack of FIVE...

NIB/NOS Campagnolo MTB O.R. Cantilever Brake Mount Bolts (Pair)

Replacement mounting bolts for your 1980's and 1990's Campy OffRoad cantilever brakes.  Record O.R., Centaur, Euclid, Olympus, etc. Condition New old stock in sealed package Details Pair (2 bolts)

NOS Vintage Phil Wood Knurled Track Lockring: For 3-Piece Hubs - Left Thread 1.32" x 24 TPI

These are the ridged lock rings that came with early Phil Wood 3 piece pista hubs from the 1970's and early 1980's.  The left hand threaded ring's diameter is 1.32" x 24 TPI, which fits Phil Wood and Campagnolo track hubs.  Stupid rare...

NOS Campagnolo Record 8-Speed Cassette Lockring: 29mm Threads, 38.5mm O.D. For 12t / 13t / 14t First Cog

Stock lock ring provided with 8 speed Campy Record cassettes, model CS-001V.  38.5mm flange diameter, to be used with 12t, 13t, 14t, or 15t smallest cog.  29mm threads fit all 8 speed freehub bodies except Record Titanium. Condition New old...

Shimano 10 Speed Chain Pin

This is the only way to connect your genuine Shimano 10 speed chain.  Includes one pin. Condition New Details Width: 6.1mm